![timer programming directsoft6 timer programming directsoft6](http://www.plcdev.com/files/plcdev/images/Views.png)
- TIMER PROGRAMMING DIRECTSOFT6 MANUALS
- TIMER PROGRAMMING DIRECTSOFT6 SOFTWARE
- TIMER PROGRAMMING DIRECTSOFT6 PC
Memory retentive means that when power is removed from the PLC or it switches from run to stop mode, the current value is not lost. Additional information on counters can be found at the following post. This is the secret to using counters in your programs. The Count Down will reset the current value to the set value.Īpplications that use counters always start with a timing chart. This will reset the current value to zero for the Count Up and Count Up & Down modes. Note: All of the counters will have a reset input. The output will turn on when the set value is reached. Count Up & Down – Will increment or decrement the current count value. Count Down – Will decrement down from the set point to zero. Count UP – Will increment up to the set point.
TIMER PROGRAMMING DIRECTSOFT6 SOFTWARE
It is set automatically by the software and is the same as the counter number.Ĭount Type – This can be one of the three types of counter. Example: CT1 = CTD1, CT2 = CTD2, etc.Ĭompletion Bit – This is the bit that will turn on when the counter has completed. It is automatically assigned by the counter number. This can also be a memory location (I or I2) so that the counter set value can change during program execution.Ĭurrent Value – This is the location in which you can see use the current value. The values are from 1 to 9999 for and integer and 1 to 999999999 for a double integer. Set Point – This is an integer (16 Bit) or double integer that represents the set point of the counter. (CT1 to CT250) There is only one counter (CNT) instruction in the PLC, but you can adapt it to handle any counting application that you may need.Ĭounter Number – This is a number from CT1 to CT250 to specify the counter. The Click PLC can have 250 unique counters in the program. Watch on YouTube: Click PLC Timers Click PLC COUNTERS Use the Address Picker to display the real-time clock from SD19 to SD26.Īdditional Information on the real-time clock of the Click PLC can be found here: The real-time clock is located in the SD area of memory in the PLC. Your date and time will now be synced with the PLC. Then hit the Write to PLC button at the bottom of the window.
TIMER PROGRAMMING DIRECTSOFT6 PC
Under setting, you can manually enter a date and time or select adjust to PC Clock.
![timer programming directsoft6 timer programming directsoft6](https://realpars.com/wp-content/uploads/2020/04/Timer-Program.png)
You will notice that it will display both the date and time in the PLC as well as the computer. When online select the following from the top menu. To set the clock in the PLC to match the PC (computer), call up the following Calendar/Clock Setup window.
![timer programming directsoft6 timer programming directsoft6](https://cdn.automationdirect.com/images/products/categories/p3_t_sw_directlogic.jpg)
The Click PLC can come with a real time clock. Timers in the Click PLC by default are not memory retentive. Additional information on timers can be found at the following post. This is the secret to using timers in your programs. You will see in the diagram above the timing chart is displayed to show you the difference.Ĭurrent Value Option – This is used to determine if the timer will be reset with the enabling rung or it will require a separate reset rung.Īpplications that use timers always start with a timing chart. Example: T1 = TD1, T2 = TD2, etc.ĭelay Setting – The delay setting is used to determine if you would like an ON Delay timer or an OFF Delay timer.
![timer programming directsoft6 timer programming directsoft6](https://plc247.com/wp-content/uploads/2020/05/plc247-com-avatar-150x150.png)
It is automatically assigned by the timer number. Unit – This can be set for milliseconds (ms), seconds (sec), minutes (min), hours (hour) or days (day).Ĭurrent Value – This is the location in which you can see use the current value. This can also be a memory location so that the timer set value can change during program execution. Set Point – This is an integer (16 Bit) that represents the set point of the timer. Timer Number – This is a number from T1 to T500 to specify the timer. (T1 to T500) There is only one timer (TMR) instruction in the PLC, but you can adapt it to handle any timing application that you may need. The Click PLC can have 500 unique timers in the program.
TIMER PROGRAMMING DIRECTSOFT6 MANUALS
The programming software and manuals can be downloaded from the Automation Direct website free of charge. Continuing our series, we will now look at timers and counters and how they are used in the Click PLC.